tar1090/html/config.js

// --------------------------------------------------------
//
// This file is to configure the configurable settings.
//
// --------------------------------------------------------
"use strict";
// -- Title Settings --------------------------------------
// Show number of aircraft and/or messages per second in the page title
//PlaneCountInTitle = false;
//MessageRateInTitle = false;

// -- Output Settings -------------------------------------
// The DisplayUnits setting controls whether nautical (ft, NM, knots), 
// metric (m, km, km/h) or imperial (ft, mi, mph) units are used in the 
// plane table and in the detailed plane info. Valid values are
// "nautical", "metric", or "imperial".
//DisplayUnits = "nautical";

// -- Map settings ----------------------------------------
// These settings are overridden by any position information
// provided by dump1090 itself. All positions are in decimal
// degrees.

// Default center of the map.
//DefaultCenterLat = 45.0;
//DefaultCenterLon = 9.0;
// The google maps zoom level, 0 - 16, lower is further out
//DefaultZoomLvl   = 7;

// Center marker. If dump1090 provides a receiver location,
// that location is used and these settings are ignored.

//SiteShow    = false;           // true to show a center marker
//SiteLat     = 45.0;            // position of the marker
//SiteLon     = 9.0;
//SiteName    = "My Radar Site"; // tooltip of the marker

// Color controls for the range outline
//range_outline_color = '#0000DD';
//range_outline_width = 1.7;
//range_outline_colored_by_altitude = false;

// which map is displayed to new visitors
// valid values:
// terrain_roads
// osm
// wikimedia
// terrain_roads
// terrain
// carto_light_all
// carto_light_nolabels
// carto_dark_all
// carto_dark_nolabels
// only with bing key:
// bing_aerial
// bing_roads

// which map is displayed to new visitors
//MapType_tar1090 = "carto_light_all";

// Default map dim state, true or false.
//MapDim = true;


// -- Marker settings -------------------------------------

//markerScaleFactor = 1.2;
//markerMaxSize = 1.32;
//markerMinSize = 0.72;

//lineWidth = 1;

// These settings control the coloring of aircraft by altitude.
// All color values are given as Hue (0-359) / Saturation (0-100) / Lightness (0-100)
//
// To enable these colors instead of the defaults, remove the /* and */ above and below the next block

/*

ColorByAlt = {
	// HSL for planes with unknown altitude:
	unknown : { h: 0,   s: 0,   l: 30 },

	// HSL for planes that are on the ground:
	ground  : { h: 0, s: 0, l: 45 },

	air : {
		// These define altitude-to-hue mappings
		// at particular altitudes; the hue
		// for intermediate altitudes that lie
		// between the provided altitudes is linearly
		// interpolated.
		//
		// Mappings must be provided in increasing
		// order of altitude.
		//
		// Altitudes below the first entry use the
		// hue of the first entry; altitudes above
		// the last entry use the hue of the last
		// entry.
		h: [ { alt: 2000,  val: 20 },    // orange
			 { alt: 10000, val: 140 },   // light green
			 { alt: 40000, val: 300 } ], // magenta
		s: 88,
		l: 44,
	},

	// Changes added to the color of the currently selected plane
	selected : { h: 0, s: -10, l: +20 },

	// Changes added to the color of planes that have stale position info
	stale :    { h: 0, s: -10, l: +30 },

	// Changes added to the color of planes that have positions from mlat
	mlat :     { h: 0, s: -10, l: -10 }
};

*/

// For a monochrome display try this:
// ColorByAlt = {
//         unknown :  { h: 0, s: 0, l: 40 },
//         ground  :  { h: 0, s: 0, l: 30 },
//         air :      { h: [ { alt: 0, val: 0 } ], s: 0, l: 50 },
//         selected : { h: 0, s: 0, l: +30 },
//         stale :    { h: 0, s: 0, l: +30 },
//         mlat :     { h: 0, s: 0, l: -10 }
// };

// Outline color for aircraft icons with an ADS-B position
//OutlineADSBColor = '#000000';

// Outline color for aircraft icons with a mlat position
//OutlineMlatColor = '#4040FF';

// Range rings

// Also called range rings :)
//SiteCircles = true; // true to show circles (only shown if the center marker is shown)
// In miles, nautical miles, or km (depending settings value 'DisplayUnits')
//SiteCirclesDistances = new Array(100,150,200,250);

// Controls page title, righthand pane when nothing is selected
//PageName = "tar1090";

// Show country flags by ICAO addresses?
//ShowFlags = true;

// Set to false to disable the ChartBundle base layers (US coverage only)
//ChartBundleLayers = true;

// Provide a Bing Maps API key here to enable the Bing imagery layer.
// You can obtain a free key (with usage limits) at
// https://www.bingmapsportal.com/ (you need a "basic key")
//
// Be sure to quote your key:
//   BingMapsAPIKey = "your key here";
//
BingMapsAPIKey = null;

// This determines what is up, default is north (0 degrees)
//mapOrientation = 0;

// Only display labels when zoomed in this far:
//labelZoom = 8;
//labelZoomGround = 12.5;

//labelFont = 'bold 12px tahoma';

//displayUATasADSB = false;
//uatNoTISB = true;

// Don't display any TIS-B planes
// filterTISB = false;

//flightawareLinks = false;

// Filter implausible positions (required speed > Mach 3.5)
// positionFilter = true;
// positionFilterSpeed = 3.5; // in Mach
// filter speed is based on transmitted ground speed if available
// this factor is used to give the actual filter speed
// positionFilterGsFactor = 1.8;
// debugPosFilter = false; // draw red dots for filtered positions

// altitudeFilter = true;

// time in seconds before an MLAT position is accepted after receiving a
// more reliable position
//mlatTimeout = 30;

// enable/disable mouseover/hover aircraft information
//enableMouseover = true;

// enable/disable temporary aircraft trails
//tempTrails = false;
//tempTrailsTimeout = 90;

// Columns that have a // in front of them are shown.
HideCols = [
	"#icao",
//	"#flag",
//	"#flight",
	"#registration",
//	"#aircraft_type",
//	"#squawk",
//	"#altitude",
//	"#speed",
	"#vert_rate",
//	"#distance",
	"#track",
	"#msgs",
	"#seen",
//	"#rssi",
	"#lat",
	"#lon",
	"#data_source",
]


//enableDWD = true;